• Aqua DL-65 Top PU

    Article No. 720201

    Aqua DL-65 Top PU

    Water-based topcoat for windows, doors and other high-value wood elements

    Degree of gloss
    Colour: white (RAL 9016) | 7202
    Colour: white (RAL 9016) | 7202
    Please choose a colour
    Size / Quantity

    Brochures and Catalogues

    product.brochures.loading

    Product specifications

    Binder Special PU/acrylate polymers
    Density Approx. 1.2 g/cm³
    Odour Mild, odourless once dry
    Degree of gloss Matt, silk matt, silk gloss

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • For professional users only
    • For use on interior and exterior wood
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • On many more substrates with Aqua AG-26-All Primer
    • Intermediate and finishing coats
    • Can also be used as a maintenance coat
    • Not suitable for coating flooring (terraces, wooden decking, etc.)
    • For use by professionals

    Properties

    • Water-based
    • Resistant to yellowing
    • Easy to apply
    • Good edge coverage
    • Weatherproof and moisture-regulating
    • High PU content: long-lasting, dirt-repellent, hard-wearing
    • Excellent flow properties
    • Block resistant (in accordance with Code of Practice HO.03)
    • Low odour
    • Very good hiding power
    • Highly elastic
    • Exceptional adherence on old coatings when used for maintenance work.
    • Preparation
      • Substrate requirements

        The substrate must be clean, dust-free and dry.

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Thoroughly sand any old coatings that are still intact.

        Sand grey and weathered wood surfaces down to sound, bright wood.

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

        Pre-treat exterior wood that is to be protected from soft rot and blue stain with Aqua IG-15-Impregnation Primer IT* - not necessary for interior wood (*use biocides safely. Always read the label and product information before use).

        If a white or light-coloured top coat is used, to avoid bleeding of coloured substances contained in the wood pre-treat with Aqua AG-26 All Primer

    • Application
      • Application temperature: min. 10 °C max. 25 °C
      • Stir before use
      • By brush / By roller Airless/airmix spraying / Flow cup gun
      • Stir well.

        Apply with a brush, roller or by spraying.

        Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.

        Airless spraying: nozzle size: 0.28-0.33 mm; material pressure: 90-120 bar.

        Air-mix spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar, atomiser air pressure 1-2 bar.

        Apply further coats once dry.

        Apply 2 - 3 coats with a slight intermediate sanding.

        If the substrate has been pre-treated with Aqua AG-26 All Primer, 1-2 coats are suffcient.

        Maintenance coating: 1 - 2 coats with a slight intermediate sanding.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Prior to full application, please apply a test coat to a sample area under practical conditions using the desired system, then test or examine the surface properties.

        Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Do not use at temperatures below +5°C.

        If the temperature is too low or the humidity too high, it will take longer for the material to reach the desired properties.

        If the temperature is too high or the humidity too low, the material will dry more quickly. In such cases, we recommend adding Aqua OZA-90 Open Time Additive.

        Divide large surfaces into strips and do not coat extensive areas all at once.

        Areas that are being coated or dried should be protected against rain, wind, sunlight and condensation.

        Bright, intense colours such as yellow, orange and red may have a lower covering capacity as a natural consequence of the pigments used. When using these colours, it is therefore recommended either to first apply a coat of a similar colour with a greater covering capacity, or to apply a second coat in the desired colour.

         

        Gaskets that contain plasticizers tend to become sticky in conjunction with dispersion paints. Use plasticizer-free gaskets.

        Sealing compounds must be compatible with the coating and may only be applied once the coating has dried thoroughly.

        Please check paint compatibility with plasticised seals in advance, alternatively use plasticiser-free products (e.g. TPE seals).

      • Drying

        Dust dry: approx. 30 minutes
        Touch dry: approx. 1 hour
        Overcoating: approx. 4 hours

         

        Practice values at +20 °C and 65% relative humidity.

        The coating may take significantly longer to dry thoroughly in lower temperatures, at high humidity or if the maximum layer thickness has been exceeded.

      • Thinning

        If necessary, thin with up to 5% water or Aqua OZA-90 Open Time Additive.

    • Working tools / cleaning
      • By brush / By roller Airless/airmix spraying / Flow cup gun
      • Paintbrush with synthetic bristles, flat brush, flow cup gun, airless/airmix spraying equipment

         

        Clean tools immediately after use with water and detergent.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

    • Usage
      • Approx. 100 ml / m² per layer applied
      • Approx. 100 ml/m² per coat

    • General information
      • DIN EN 71-3 "Migration of certain elements":

        This product complies with the limits for the migration of heavy metals to children's toys according to DIN EN 71-3 and thus fulfils one of several further requirements for the safety of children's toys according to the EU "Toy Directive" (2009/48/EC).

        On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces.
        The only remedy for this is pre-weathering or very coarse sanding (P80).
        If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

        Observe the regulations concerning design principles for wood protection.

        Do not use on horizontal surfaces without drainage slopes and without edge radius, avoid accumulated moisture.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.