Article No. 387601
Fire-resistant, light-fast, durable 1K colour varnish
Product specifications
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Wood and wood-based materials
- High-quality furniture
- Interior finishing work: e.g. panels, borders, cladding & interior doors
- Especially suitable for use on surfaces that have been pre-treated with Remmers Aqua fillers
- As a glass lacquer (in combination with Aqua VGA-485)
Properties
- Single-component: simple and economical handling
- Can also be used on vertical surfaces
- Good flow properties
- Good hiding power
- Quick-drying
- Short time until ready for stacking
- Good resistance to chemicals
- Good resistance to a wide range of commercially available hand creams
- Fire behaviour according to DIN EN 13501-1: B-s1,d0 on suitable substrates
- Suitable for interior finishing of ships (IMO)
- Lightfast
- 2K-ready: add 2% Aqua VGA-485 to improve the resistance to chemicals and scratches, as well as adhesion to glass and primer films
-
Preparation
-
Substrate requirements
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood moisture content: 8-12%
-
Preparations
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.
Clean glass using V-893.
Thoroughly sand any old coatings that are still intact.
Sand wood using P 100 - 180 grit.
Sand panels using P 180 - 320 grit.
Sand filler using P 240 - 320 grit.
-
-
Application
-
Stir well.
Spray.
Apply by roller or brush (only when diluted).
Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.
Carry out intermediate sanding (P 240 - 320) before subsequent coats.
Seal opened containers well and use contents as soon as possible.
-
Application instructions
-
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.
On non-wood substrates such as glass, sanded priming films, melamine resins and PU paints, adhesion can be significantly improved by adding Aqua VGA-485. Owing to the large number of possible material variants, careful checking must be carried out prior to application.
To ensure optimum resistance to metal rings and to improve the resistance to chemicals, we recommend coating with a suitable, light-fast clear varnish.
If using as a transparent topcoat on surfaces with a colour varnish (improved resistance to metal rings and durability), one coat is sufficient. When applying over a colour varnish, add 5-10% of the Aqua colour varnish to the clear varnish in order to counteract colour changes.
-
Drying
Practice values at +20 °C and 65% relative humidity.
Low temperatures, poor ventilation and high humidity delay drying.
-
Thinning
Ready to use; if necessary, dilute with max. 5% water and/or use max. 3% V-490 as a retarding agent.
-
Working tools / cleaning
-
Airless/Airmix spraying equipment, flow cup gun, acrylic brush, foam roller
Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.
Ensure that any residue from cleaning is disposed of correctly.
-
Storage / shelf life
-
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
-
Usage
-
120 - 150 ml/m² per coat
-
General information
-
DIN EN 71-3 "Migration of certain elements":
This product complies with the limits for the migration of heavy metals to children's toys according to DIN EN 71-3 and thus fulfils one of several further requirements for the safety of children's toys according to the EU "Toy Directive" (2009/48/EC).Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.
To preserve the quality of the surface, we recommend regular cleaning and care using a lint-free cotton cloth. Please use solvent-free and silicone-free cleaning agents.
For applications in accordance with the Marine Equipment Directive, the maximum wet application quantity is 3 x 150 µm.
-
-
Disposal instructions
-
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
-
-
Safety / regulations
-
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.
-