Article No. 321705
Highly pigmented, single-component filler with excellent sealing effect, especially for wood rich in active substances
Product specifications
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Preparing opaque, pigmented varnishes
- Solid wood & veneers
- Wood materials
- Wood types rich in active substances such as ash, Hevea, oak, whitewood/yellow poplar
- High-quality furniture
- Wooden stairs
- In damp rooms (kitchens and bathrooms)
- Interior finishing work: e.g. panels, borders, cladding & interior doors
Properties
- Single-component: simple and economical handling
- Excellent sealing effect (moisture and water-soluble substances in the wood)
- Primer for coatings that emphasise pores
- Good sanding properties
- Low risk of wearing through
- Can be coated over with Aqua and PUR varnishes
-
Preparation
-
Substrate requirements
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood moisture content: 8-12%
-
Preparations
Wash off greasy or resin-rich woods/substrates with WV-891 or V-890. Use UN-894 indoors on the construction site. Ensure good ventilation for solvents.
Softwoods: sand with P 80 - 120.
All other substrates: sand with P 180 - 320.
-
-
Application
-
Stir well.
Spray.
Airless spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 120 bar.
Airmix spraying: nozzle size: 0.23 - 0.28 mm, material pressure: 80 - 100 bar, atomiser air pressure: 1.2 - 2 bar.
Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
Once dry, carry out intermediate sanding with P 240-320.
Repeat the process if necessary.
Intermediate and final coats of suitable products can be applied after drying.
Seal opened containers well and use contents as soon as possible.
-
-
Application instructions
-
Woods rich in active substances must be primed twice for optimum isolation.
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
Before coating technically modified woods and wood-based materials, apply the product to a trial surface and conduct a suitability test on the desired area of use.
-
Drying
Dust-dry: after approx. 1 hour
Can be overcoated: after approx. 4 hours
Drying overnight improves the sealing effect (e.g. on Hevea)Practice values at +20 °C and 65% relative humidity.
Low temperatures, poor ventilation and high humidity delay drying.
-
Thinning
Ready to use
-
-
Working tools / cleaning
-
Airless/Airmix spraying equipment, flow cup gun
-
Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.
-
-
Storage / shelf life
-
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
-
-
Usage
-
120 - 150 ml/m² per coat
-
-
General information
-
The product’s insulating effect may be impaired if it is diluted too thinly, if the wood is too wet or if the recommended coating sequence, application volumes and drying times are not observed. With water-based coating systems, there is always the residual risk that substances contained in the wood will leach out.
-
-
Disposal instructions
-
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
-
-
Safety / regulations
-
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.
-
